CDNWiki
View Source:
MencoderCommands
mencoder -dvd-device /dev/sr0 dvd://1 -aid 128 -sid 0 -ovc lavc -oac lavc -lavcopts vcodec=mpeg4:vpass=1:vbitrate=700:acodec=mp3:abitrate=192 -vf harddup -o video.avi mencoder -dvd-device /dev/sr0 dvd://1 -aid 128 -ovc lavc -oac lavc -lavcopts vcodec=mpeg4:vpass=1:vbitrate=700:vhq:trell:acodec=mp3:abitrate=192 -vf harddup -o video.avi Extract subtitles (why?) mencoder -dvd-device /dev/sr0 dvd://1 -vo copy -ao copy -o /dev/null -vobsubout video-english -vobsuboutid eng !!!Start Here !!Ogg-Vorbis audio is not compatible with AVI containers. You must mux it separately. Extract audio <verbatim> mplayer dvd://1 -alang en -ao pcm:fast:waveheader:audio.wav -vc null -vo null </verbatim> Encode audio <verbatim> oggenc --quality 4.0 -o audio.ogg audio.wav </verbatim> Use a pipe to streamline the previous two <verbatim> mkfifo -m600 audio.pipe </verbatim> These two must be run simultaneously (source first) and cannot be backgrounded. <verbatim> mplayer dvd://1 -alang en -ao pcm:fast:waveheader:file=audio.pipe -vc null -vo null oggenc --quality 4.0 -o audio2.ogg audio.pipe rm audio.pipe </verbatim> Calculate target bitrate from movie length and encoded audio size<br> movie length: 7446 seconds <verbatim> video_space=$(((700 * 8388608) - $(stat -c '%s' audio.ogg) )) video_length=7446 video_bitrate=$(( (${video_space} / ${video_length}) / 1024)) mencoder dvd://1 -sid 0 -noaudio -ovc lavc -lavcopts vcodec=mpeg4:vpass=1:vbitrate=${video_bitrate}:vhq:trell \ -vf harddup -o /dev/null mencoder dvd://1 -sid 0 -audiofile audio.ogg -sid 0 -ovc lavc -oac copy -lavcopts \ vcodec=mpeg4:vpass=2:vbitrate=${video_bitrate}:vhq:trell -vf harddup -o video.avi </verbatim> * -ss - selects a start time in seconds or hh:mm:ss.mmm - Note that this is not accurate--it will start at the first keyframe after the chosen timeframe. * -endpos - specifies the number of seconds to encode before stopping *Mencoer* *options* *are* *poorly* *documented!* If 'Skipping frame!' or '1 duplicate frame(s)!' warnings occur repeatedly, and the resultant audio grows out of sync (as if one is faster) then try tweaking the source framerate. 'skipping frame' means there's too many frames coming in, so try a lower fps. 'duplicate frame' means there isn't enough frames coming in to satisfy the outgoing framerate, so try a higher source fps. Try and tweak so that there are as few of each message as possible. * -fps <decimal|fraction> - specifies the source framerate. The fraction can be, for instance, 24000/1001 for 23.976fps. * -ofps <decimal|fraction> - specifies the output frame rate. This must be set to the actual real framerate of the source, so that the frames line up with the audio. ( In two samples, the settings that got near-perfect results were '-fps 22000/1020 -ofps 24000/1001' ) -- mencoder doesn't support rendering SSA/ASS subtitles, and renders them as regular text. Very ugly.<br> To get around this, you can pre-render using mplayer. Beware, this takes an obscene amount of disk space (raw video frames) <verbatim> mplayer -ass -sub file.ass -vo yuv4mpeg file.avi mplayer -sid 0 -vo yuv4mpeg file.avi </verbatim> <verbatim> # dump video mplayer -nosound -noframedrop -noautosub -vo yuv4mpeg:file=stream.y4m 300_F2_1080P.mov # dump audio mplayer -vo null -vc null -ao pcm:fast 300_F2_1080P.mov # Encode mencoder stream.y4m -audiofile audiodump.wav -fps 24000/1001 -o test.mpeg -of mpeg -mpegopts format=dvd:tsaf -srate 48000 -ofps 25 -ovc lavc -oac lavc -lavcopts vcodec=mpeg2video:vrc_buf_size=1835:keyint=15:vrc_maxrate=9800:vbitrate=4900:aspect=24/10:acodec=ac3:abitrate=192 -vf scale=720:300,expand=720:300,harddup </verbatim> * harddup - AVI containers are fine with default frame syncing, but others (mpeg, flv) may require harddup when changing framerates, to maintain A/V sync
